Merge v4.7.10 which is latest 4.7.y stable version. #16

bkrepo · 2016-10-28T07:33:59Z

No description provided.

commit 3d95182 upstream. Back when I submitted the GSO code I messed up and dropped the support for disabling the VLAN tag filtering via the feature bit. This patch re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the VLAN filtering independent of toggling promiscuous mode. Fixes: b83e301 ("ixgbe/ixgbevf: Add support for GSO partial") Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 0066c8b upstream. Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and igb_ptp_rx_rgtstamp. Add PHY delay compensation in igb_ptp_rx_pktstamp(). In the IGB driver, there are two functions that retrieve timestamps received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp(). The previous commit only changed igb_ptp_rx_rgtstamp(), and the change was incorrect. There are two instances in which PHY delay compensations should be made: - Before the packet transmission over the PHY, the latency between when the packet is timestamped and transmission of the packets, should be an add operation, but it is currently a subtract. - After the packets are received from the PHY, the latency between the receiving and timestamping of the packets should be a subtract operation, but it is currently an add. Signed-off-by: Kshitiz Gupta <[email protected]> Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency) Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit a83f1fc upstream. Commit 0259f52 ('soc/tegra: pmc: Restore base address on probe failure') fixes an issue where the PMC base address pointer is not restored on probe failure. However, this fix creates another problem where if early initialisation of the PMC driver fails and an initial mapping for the PMC address space is not created, then when the PMC device is probed, the PMC base address pointer will not be valid and this will cause a crash when tegra_pmc_init() is called and attempts to access a register. Although the PMC address space is mapped a 2nd time during the probe and so this could be fixed by populating the base address pointer earlier during the probe, this adds more complexity to the code. Moreover, the PMC probe also assumes the the soc data pointer is also initialised when the device is probed and if not will also lead to a crash when calling tegra_pmc_init_tsense_reset(). Given that if the early initialisation does fail then something bad has happen, it seems acceptable to allow the PMC device probe to fail as well. Therefore, if the PMC base address pointer or soc data pointer are not valid when probing the PMC device, WARN and return an error. Fixes: 0259f52 ('soc/tegra: pmc: Restore base address on probe failure') Signed-off-by: Jon Hunter <[email protected]> Signed-off-by: Thierry Reding <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit f4cceb2 upstream. If kmap fails, it leads to memory corruption. Fixes: f64122c ('drm: add new QXL driver. (v1.4)') Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> Link: http://patchwork.freedesktop.org/patch/msgid/20160711084633.GA31411@mwanda Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 8a545f1 upstream. We can't pass error pointers to kfree() or it causes an oops. Fixes: 52b209f ('get rid of hostfs_read_inode()') Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Richard Weinberger <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit c3cee37 upstream. If the total amount of memory assigned to quarantine is less than the amount of memory assigned to per-cpu quarantines, |new_quarantine_size| may overflow. Instead, set it to zero. [[email protected]: cleanup: use WARN_ONCE return value] Link: http://lkml.kernel.org/r/[email protected] Fixes: 55834c5 ("mm: kasan: initial memory quarantine implementation") Signed-off-by: Alexander Potapenko <[email protected]> Reported-by: Dmitry Vyukov <[email protected]> Cc: Andrey Ryabinin <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 4b3ec5a upstream. Currently we call quarantine_reduce() for ___GFP_KSWAPD_RECLAIM (implied by __GFP_RECLAIM) allocation. So, basically we call it on almost every allocation. quarantine_reduce() sometimes is heavy operation, and calling it with disabled interrupts may trigger hard LOCKUP: NMI watchdog: Watchdog detected hard LOCKUP on cpu 2irq event stamp: 1411258 Call Trace: <NMI> dump_stack+0x68/0x96 watchdog_overflow_callback+0x15b/0x190 __perf_event_overflow+0x1b1/0x540 perf_event_overflow+0x14/0x20 intel_pmu_handle_irq+0x36a/0xad0 perf_event_nmi_handler+0x2c/0x50 nmi_handle+0x128/0x480 default_do_nmi+0xb2/0x210 do_nmi+0x1aa/0x220 end_repeat_nmi+0x1a/0x1e <<EOE>> __kernel_text_address+0x86/0xb0 print_context_stack+0x7b/0x100 dump_trace+0x12b/0x350 save_stack_trace+0x2b/0x50 set_track+0x83/0x140 free_debug_processing+0x1aa/0x420 __slab_free+0x1d6/0x2e0 ___cache_free+0xb6/0xd0 qlist_free_all+0x83/0x100 quarantine_reduce+0x177/0x1b0 kasan_kmalloc+0xf3/0x100 Reduce the quarantine_reduce iff direct reclaim is allowed. Fixes: 55834c5("mm: kasan: initial memory quarantine implementation") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Andrey Ryabinin <[email protected]> Reported-by: Dave Jones <[email protected]> Acked-by: Alexander Potapenko <[email protected]> Cc: Dmitry Vyukov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 12eb513 upstream. There exists a race where the application can setup a connection and then disconnect it before iw_cxgb4 processes the fw4_ack message. For passive side connections, the fw4_ack message is used to know when to stop the ep timer for MPA_REPLY messages. If the application disconnects before the fw4_ack is handled then c4iw_ep_disconnect() needs to clean up the timer state and stop the timer before restarting it for the disconnect timer. Failure to do this results in a "timer already started" message and a premature stopping of the disconnect timer. Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation") Signed-off-by: Steve Wise <[email protected]> Signed-off-by: Doug Ledford <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 15f6d33 upstream. On May 4th, Bjørn Mork provided patch 697bbc7 ("builddeb: include objtool binary in headers package"). However, that one only works if $srctree=$objtree, because the objtool binaries are not written to the srctree, but to the objtree. Signed-off-by: Wilfried Klaebe <[email protected]> Fixes: 697bbc7 ("builddeb: include objtool binary in headers package") Signed-off-by: Michal Marek <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 28b89b9 upstream. A discrepancy between cpu_online_mask and cpuset's effective_cpus mask is inevitable during hotplug since cpuset defers updating of effective_cpus mask using a workqueue, during which time nothing prevents the system from more hotplug operations. For that reason guarantee_online_cpus() walks up the cpuset hierarchy until it finds an intersection under the assumption that top cpuset's effective_cpus mask intersects with cpu_online_mask even with such a race occurring. However a sequence of CPU hotplugs can open a time window, during which none of the effective CPUs in the top cpuset intersect with cpu_online_mask. For example when there are 4 possible CPUs 0-3 and only CPU0 is online: ======================== =========================== cpu_online_mask top_cpuset.effective_cpus ======================== =========================== echo 1 > cpu2/online. CPU hotplug notifier woke up hotplug work but not yet scheduled. [0,2] [0] echo 0 > cpu0/online. The workqueue is still runnable. [2] [0] ======================== =========================== Now there is no intersection between cpu_online_mask and top_cpuset.effective_cpus. Thus invoking sys_sched_setaffinity() at this moment can cause following: Unable to handle kernel NULL pointer dereference at virtual address 000000d0 ------------[ cut here ]------------ Kernel BUG at ffffffc0001389b0 [verbose debug info unavailable] Internal error: Oops - BUG: 96000005 [tobetter#1] PREEMPT SMP Modules linked in: CPU: 2 PID: 1420 Comm: taskset Tainted: G W 4.4.8+ torvalds#98 task: ffffffc06a5c4880 ti: ffffffc06e124000 task.ti: ffffffc06e124000 PC is at guarantee_online_cpus+0x2c/0x58 LR is at cpuset_cpus_allowed+0x4c/0x6c <snip> Process taskset (pid: 1420, stack limit = 0xffffffc06e124020) Call trace: [<ffffffc0001389b0>] guarantee_online_cpus+0x2c/0x58 [<ffffffc00013b208>] cpuset_cpus_allowed+0x4c/0x6c [<ffffffc0000d61f0>] sched_setaffinity+0xc0/0x1ac [<ffffffc0000d6374>] SyS_sched_setaffinity+0x98/0xac [<ffffffc000085cb0>] el0_svc_naked+0x24/0x28 The top cpuset's effective_cpus are guaranteed to be identical to cpu_online_mask eventually. Hence fall back to cpu_online_mask when there is no intersection between top cpuset's effective_cpus and cpu_online_mask. Signed-off-by: Joonwoo Park <[email protected]> Acked-by: Li Zefan <[email protected]> Cc: Tejun Heo <[email protected]> Cc: [email protected] Cc: [email protected] Signed-off-by: Tejun Heo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9157056 upstream. On the v2 hierarchy, "cgroup.subtree_control" rejects controller enables if the cgroup has processes in it. The enforcement of this logic assumes that the cgroup wouldn't have any css_sets associated with it if there are no tasks in the cgroup, which is no longer true since a79a908 ("cgroup: introduce cgroup namespaces"). When a cgroup namespace is created, it pins the css_set of the creating task to use it as the root css_set of the namespace. This extra reference stays as long as the namespace is around and makes "cgroup.subtree_control" think that the namespace root cgroup is not empty even when it is and thus reject controller enables. Fix it by making cgroup_subtree_control() walk and test emptiness of each css_set instead of testing whether the list_head is empty. While at it, update the comment of cgroup_task_count() to indicate that the returned value may be higher than the number of tasks, which has always been true due to temporary references and doesn't break anything. Signed-off-by: Tejun Heo <[email protected]> Reported-by: Evgeny Vereshchagin <[email protected]> Cc: Serge E. Hallyn <[email protected]> Cc: Aditya Kali <[email protected]> Cc: Eric W. Biederman <[email protected]> Fixes: a79a908 ("cgroup: introduce cgroup namespaces") Link: systemd/systemd#3589 (comment) Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit e436fd6 upstream. be7635e ("arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections") added .softirqentry.text section, but it was not added to recordmcount. So functions in the section are untracable. Add the section to scripts/recordmcount.c and scripts/recordmcount.pl. Fixes: be7635e ("arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Dmitry Vyukov <[email protected]> Acked-by: Steve Rostedt <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit f6d7c1b upstream. This fixes subpage writes when using 4-bit HW ECC. There has been numerous reports about ECC errors with devices using this driver for a while. Also the 4-bit ECC has been reported as broken with subpages in [1] and with 16 bits NANDs in the driver and in mach* board files both in mainline and in the vendor BSPs. What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to try reinitializing the ECC engine: - R/W on whole pages properly generates/checks RS code - try writing the 1st subpage only of a blank page, the subpage is well written and the RS code properly generated, re-reading the same page the HW detects some ECC error, reading the same page again no ECC error is detected Note that the ECC engine is already reinitialized in the 1-bit case. Tested on my LCDK with UBI+UBIFS using subpages. This could potentially get rid of the issue workarounded in [1]. [1] 28c015a ("mtd: davinci-nand: disable subpage write for keystone-nand") Fixes: 6a4123e ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by: Karl Beldan <[email protected]> Acked-by: Boris Brezillon <[email protected]> Signed-off-by: Brian Norris <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 5b398e4 upstream. I hit the following hung task when runing a OOM LTP test case with 4.1 kernel. Call trace: [<ffffffc000086a88>] __switch_to+0x74/0x8c [<ffffffc000a1bae0>] __schedule+0x23c/0x7bc [<ffffffc000a1c09c>] schedule+0x3c/0x94 [<ffffffc000a1eb84>] rwsem_down_write_failed+0x214/0x350 [<ffffffc000a1e32c>] down_write+0x64/0x80 [<ffffffc00021f794>] __ksm_exit+0x90/0x19c [<ffffffc0000be650>] mmput+0x118/0x11c [<ffffffc0000c3ec4>] do_exit+0x2dc/0xa74 [<ffffffc0000c46f8>] do_group_exit+0x4c/0xe4 [<ffffffc0000d0f34>] get_signal+0x444/0x5e0 [<ffffffc000089fcc>] do_signal+0x1d8/0x450 [<ffffffc00008a35c>] do_notify_resume+0x70/0x78 The oom victim cannot terminate because it needs to take mmap_sem for write while the lock is held by ksmd for read which loops in the page allocator ksm_do_scan scan_get_next_rmap_item down_read get_next_rmap_item alloc_rmap_item #ksmd will loop permanently. There is no way forward because the oom victim cannot release any memory in 4.1 based kernel. Since 4.6 we have the oom reaper which would solve this problem because it would release the memory asynchronously. Nevertheless we can relax alloc_rmap_item requirements and use __GFP_NORETRY because the allocation failure is acceptable as ksm_do_scan would just retry later after the lock got dropped. Such a patch would be also easy to backport to older stable kernels which do not have oom_reaper. While we are at it add GFP_NOWARN so the admin doesn't have to be alarmed by the allocation failure. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: zhong jiang <[email protected]> Suggested-by: Hugh Dickins <[email protected]> Suggested-by: Michal Hocko <[email protected]> Acked-by: Michal Hocko <[email protected]> Acked-by: Hugh Dickins <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9abefcb upstream. A timer was used to restart after the bus-off state, leading to a relatively large can_restart() executed in an interrupt context, which in turn sets up pinctrl. When this happens during system boot, there is a high probability of grabbing the pinctrl_list_mutex, which is locked already by the probe() of other device, making the kernel suspect a deadlock condition [1]. To resolve this issue, the restart_timer is replaced by a delayed work. [1] victronenergy/venus#24 Signed-off-by: Sergei Miroshnichenko <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit e1bfc11 upstream. cr4_init_shadow() will panic on 486-like machines without CR4. Fix it using __read_cr4_safe(). Reported-by: [email protected] Signed-off-by: Andy Lutomirski <[email protected]> Reviewed-by: Borislav Petkov <[email protected]> Cc: Borislav Petkov <[email protected]> Cc: Brian Gerst <[email protected]> Cc: Denys Vlasenko <[email protected]> Cc: H. Peter Anvin <[email protected]> Cc: Josh Poimboeuf <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Fixes: 1e02ce4 ("x86: Store a per-cpu shadow copy of CR4") Link: http://lkml.kernel.org/r/43a20f81fb504013bf613913dc25574b45336a61.1475091074.git.luto@kernel.org Signed-off-by: Ingo Molnar <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

… CPUID commit 05fb3c1 upstream. Otherwise arch_task_struct_size == 0 and we die. While we're at it, set X86_FEATURE_ALWAYS, too. Reported-by: David Saggiorato <[email protected]> Tested-by: David Saggiorato <[email protected]> Signed-off-by: Andy Lutomirski <[email protected]> Cc: Borislav Petkov <[email protected]> Cc: Brian Gerst <[email protected]> Cc: Dave Hansen <[email protected]> Cc: Denys Vlasenko <[email protected]> Cc: H. Peter Anvin <[email protected]> Cc: Josh Poimboeuf <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Fixes: aaeb5c01c5b ("x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86") Link: http://lkml.kernel.org/r/8de723afbf0811071185039f9088733188b606c9.1475103911.git.luto@kernel.org Signed-off-by: Ingo Molnar <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 90fd68d upstream. The udl damage handler is supposed to render 'height' lines, but its iterator has an obvious typo that makes it miss most lines if the rectangle does not cover 0/0. Fix the damage handler to correctly render all lines. This is a fallout from: commit e375882 Author: Noralf Trønnes <[email protected]> Date: Thu Apr 28 17:18:37 2016 +0200 drm/udl: Use drm_fb_helper deferred_io support Tested-by: poma <[email protected]> Reviewed-by: Daniel Vetter <[email protected]> Signed-off-by: David Herrmann <[email protected]> Reviewed-by: Eric Engestrom <[email protected]> Signed-off-by: Dave Airlie <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 666ca3d upstream. Signed-off-by: Ilia Mirkin <[email protected]> Signed-off-by: Ben Skeggs <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 670bb4f upstream. Add clock quirks for Jet parts. Reviewed-by: Sonny Jiang <[email protected]> Tested-by: Sonny Jiang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit ba6dea4 upstream. Whilst MPIDR values themselves are less than 32 bits, it is still perfectly valid for a DT to have #address-cells > 1 in the CPUs node, resulting in the "reg" property having leading zero cell(s). In that situation, the big-endian nature of the data conspires with the current behaviour of only reading the first cell to cause the kernel to think all CPUs have ID 0, and become resoundingly unhappy as a consequence. Take the full property length into account when parsing CPUs so as to be correct under any circumstances. Cc: Russell King <[email protected]> Signed-off-by: Robin Murphy <[email protected]> Signed-off-by: Russell King <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit d248220 upstream. Since commit 6ce0d20 ("ARM: dma: Use dma_pfn_offset for dma address translation"), dma_to_pfn() already returns the PFN with the physical memory start offset so we don't need to add it again. This fixes USB mass storage lock-up problem on systems that can't do DMA over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM can only do DMA over the first 2GB. [K2E-EVM]. What happens there is that without this patch SCSI layer sets a wrong bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2 is 0x87fffffff. This results in non DMA'ble pages being given to the USB controller and hence the lock-up. NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0. This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000 and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be 0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because USB devices are not correctly inheriting the dma_pfn_offset from the USB host controller. This will be fixed by a separate patch. Fixes: 6ce0d20 ("ARM: dma: Use dma_pfn_offset for dma address translation") Cc: Greg Kroah-Hartman <[email protected]> Cc: Santosh Shilimkar <[email protected]> Cc: Arnd Bergmann <[email protected]> Cc: Olof Johansson <[email protected]> Cc: Catalin Marinas <[email protected]> Cc: Linus Walleij <[email protected]> Reported-by: Grygorii Strashko <[email protected]> Signed-off-by: Roger Quadros <[email protected]> Signed-off-by: Russell King <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 3fdbda4 upstream. Variable adapter is incorrectly initialized. Fixes: bf00dc2 ("mwifiex: AMSDU Rx frame handling in AP mode") Signed-off-by: Heinrich Schuchardt <[email protected]> Acked-by: Amitkumar Karwar <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit cd95672 upstream. In function i40e_debug_aq parameter desc is assumed to be possibly NULL. Do not dereference it before checking the value. Fixes: f905dd6 ("i40e/i40evf: add max buf len to aq debug print helper") Signed-off-by: Heinrich Schuchardt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 10ef827 upstream. Without this, reading the "pins" in the debugfs causes kernel BUG. Fixes: 6e90889 ("pinctrl: UniPhier: add UniPhier pinctrl core support") Signed-off-by: Masahiro Yamada <[email protected]> Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 7440926 upstream. Documentation incorrectly refers to struct pinctrl_desc, where no such flag is available. Replace the name of the struct. Fixes: commit 8c4c201 ("pinctrl: move strict option to pinmux_ops") Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit e35478e upstream. We can't use a static property for all the changesets, so we now create dynamic ones for each changeset. Signed-off-by: Wolfram Sang <[email protected]> Fixes: 50a5ba8 ("i2c: mux: demux-pinctrl: add driver") Signed-off-by: Wolfram Sang <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit af06d4f upstream. 0day found a boot warning triggered in rcu_perf_writer() on !SMP kernel: WARN_ON(rcu_gp_is_normal() && gp_exp); , the root cause of which is trying to measure expedited grace periods(by setting gp_exp to true by default) when all the grace periods are normal(TINY RCU only has normal grace periods). However, such a mis-setting would only result in failing to measure the performance for a specific kind of grace periods, therefore using a WARN_ON to check this is a little overkilling. We could handle this inside rcuperf module via some error messages to tell users about the mis-settings. Therefore this patch removes the WARN_ON in rcu_perf_writer() and handles those checkings in rcu_perf_init() with plain if() code. Moreover, this patch changes the default value of gp_exp to 1) align with rcutorture tests and 2) make the default setting work for all RCU implementations by default. Suggested-by: Paul E. McKenney <[email protected]> Signed-off-by: Boqun Feng <[email protected]> Fixes: http://lkml.kernel.org/r/57411b10.mFvG0+AgcrMXGtcj%[email protected] Signed-off-by: Paul E. McKenney <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 7532468 upstream. In case of a IRQ type mismatch in of_pmu_irq_cfg() the device node for interrupt affinity isn't freed. So fix this issue by calling of_node_put(). Signed-off-by: Stefan Wahren <[email protected]> Fixes: fa8ad78 ("arm: perf: factor arm_pmu core out to drivers") Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Catalin Marinas <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 55a8210 ] When processing a packed profile in unpack_profile() described like "profile :ns::samba-dcerpcd /usr/lib*/samba/{,samba/}samba-dcerpcd {...}" a string ":samba-dcerpcd" is unpacked as a fully-qualified name and then passed to aa_splitn_fqname(). aa_splitn_fqname() treats ":samba-dcerpcd" as only containing a namespace. Thus it returns NULL for tmpname, meanwhile tmpns is non-NULL. Later aa_alloc_profile() crashes as the new profile name is NULL now. general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 6 PID: 1657 Comm: apparmor_parser Not tainted 6.7.0-rc2-dirty #16 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014 RIP: 0010:strlen+0x1e/0xa0 Call Trace: <TASK> ? strlen+0x1e/0xa0 aa_policy_init+0x1bb/0x230 aa_alloc_profile+0xb1/0x480 unpack_profile+0x3bc/0x4960 aa_unpack+0x309/0x15e0 aa_replace_profiles+0x213/0x33c0 policy_update+0x261/0x370 profile_replace+0x20e/0x2a0 vfs_write+0x2af/0xe00 ksys_write+0x126/0x250 do_syscall_64+0x46/0xf0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 </TASK> ---[ end trace 0000000000000000 ]--- RIP: 0010:strlen+0x1e/0xa0 It seems such behaviour of aa_splitn_fqname() is expected and checked in other places where it is called (e.g. aa_remove_profiles). Well, there is an explicit comment "a ns name without a following profile is allowed" inside. AFAICS, nothing can prevent unpacked "name" to be in form like ":samba-dcerpcd" - it is passed from userspace. Deny the whole profile set replacement in such case and inform user with EPROTO and an explaining message. Found by Linux Verification Center (linuxtesting.org). Fixes: 04dc715 ("apparmor: audit policy ns specified in policy load") Signed-off-by: Fedor Pchelkin <[email protected]> Signed-off-by: John Johansen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit f8bbc07 ] vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <[email protected]> Reviewed-by: Willem de Bruijn <[email protected]> Acked-by: Jason Wang <[email protected]> Reviewed-by: Eric Dumazet <[email protected]> Acked-by: Michael S. Tsirkin <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 769e6a1 ] ui_browser__show() is capturing the input title that is stack allocated memory in hist_browser__run(). Avoid a use after return by strdup-ing the string. Committer notes: Further explanation from Ian Rogers: My command line using tui is: $ sudo bash -c 'rm /tmp/asan.log*; export ASAN_OPTIONS="log_path=/tmp/asan.log"; /tmp/perf/perf mem record -a sleep 1; /tmp/perf/perf mem report' I then go to the perf annotate view and quit. This triggers the asan error (from the log file): ``` ==1254591==ERROR: AddressSanitizer: stack-use-after-return on address 0x7f2813331920 at pc 0x7f28180 65991 bp 0x7fff0a21c750 sp 0x7fff0a21bf10 READ of size 80 at 0x7f2813331920 thread T0 #0 0x7f2818065990 in __interceptor_strlen ../../../../src/libsanitizer/sanitizer_common/sanitizer_common_interceptors.inc:461 #1 0x7f2817698251 in SLsmg_write_wrapped_string (/lib/x86_64-linux-gnu/libslang.so.2+0x98251) #2 0x7f28176984b9 in SLsmg_write_nstring (/lib/x86_64-linux-gnu/libslang.so.2+0x984b9) #3 0x55c94045b365 in ui_browser__write_nstring ui/browser.c:60 #4 0x55c94045c558 in __ui_browser__show_title ui/browser.c:266 #5 0x55c94045c776 in ui_browser__show ui/browser.c:288 #6 0x55c94045c06d in ui_browser__handle_resize ui/browser.c:206 #7 0x55c94047979b in do_annotate ui/browsers/hists.c:2458 #8 0x55c94047fb17 in evsel__hists_browse ui/browsers/hists.c:3412 #9 0x55c940480a0c in perf_evsel_menu__run ui/browsers/hists.c:3527 #10 0x55c940481108 in __evlist__tui_browse_hists ui/browsers/hists.c:3613 #11 0x55c9404813f7 in evlist__tui_browse_hists ui/browsers/hists.c:3661 #12 0x55c93ffa253f in report__browse_hists tools/perf/builtin-report.c:671 #13 0x55c93ffa58ca in __cmd_report tools/perf/builtin-report.c:1141 #14 0x55c93ffaf159 in cmd_report tools/perf/builtin-report.c:1805 #15 0x55c94000c05c in report_events tools/perf/builtin-mem.c:374 #16 0x55c94000d96d in cmd_mem tools/perf/builtin-mem.c:516 #17 0x55c9400e44ee in run_builtin tools/perf/perf.c:350 #18 0x55c9400e4a5a in handle_internal_command tools/perf/perf.c:403 #19 0x55c9400e4e22 in run_argv tools/perf/perf.c:447 #20 0x55c9400e53ad in main tools/perf/perf.c:561 #21 0x7f28170456c9 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #22 0x7f2817045784 in __libc_start_main_impl ../csu/libc-start.c:360 #23 0x55c93ff544c0 in _start (/tmp/perf/perf+0x19a4c0) (BuildId: 84899b0e8c7d3a3eaa67b2eb35e3d8b2f8cd4c93) Address 0x7f2813331920 is located in stack of thread T0 at offset 32 in frame #0 0x55c94046e85e in hist_browser__run ui/browsers/hists.c:746 This frame has 1 object(s): [32, 192) 'title' (line 747) <== Memory access at offset 32 is inside this variable HINT: this may be a false positive if your program uses some custom stack unwind mechanism, swapcontext or vfork ``` hist_browser__run isn't on the stack so the asan error looks legit. There's no clean init/exit on struct ui_browser so I may be trading a use-after-return for a memory leak, but that seems look a good trade anyway. Fixes: 05e8b08 ("perf ui browser: Stop using 'self'") Signed-off-by: Ian Rogers <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Athira Rajeev <[email protected]> Cc: Ben Gainey <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: James Clark <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kajol Jain <[email protected]> Cc: Kan Liang <[email protected]> Cc: K Prateek Nayak <[email protected]> Cc: Li Dong <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Oliver Upton <[email protected]> Cc: Paran Lee <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Sun Haiyong <[email protected]> Cc: Tim Chen <[email protected]> Cc: Yanteng Si <[email protected]> Cc: Yicong Yang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 9d274c1 upstream. We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) #1 btrfs_drop_extents (fs/btrfs/file.c:411:4) #2 log_one_extent (fs/btrfs/tree-log.c:4732:9) #3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) #4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) #5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) #6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) #7 btrfs_sync_file (fs/btrfs/file.c:1933:8) #8 vfs_fsync_range (fs/sync.c:188:9) #9 vfs_fsync (fs/sync.c:202:9) #10 do_fsync (fs/sync.c:212:9) #11 __do_sys_fdatasync (fs/sync.c:225:9) #12 __se_sys_fdatasync (fs/sync.c:223:1) #13 __x64_sys_fdatasync (fs/sync.c:223:1) #14 do_syscall_x64 (arch/x86/entry/common.c:52:14) #15 do_syscall_64 (arch/x86/entry/common.c:83:7) #16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of the filesystem tree at the time of the crash: >>> root = prog.crashed_thread().stack_trace()[2]["inode"].root >>> ret, nodes, slots = btrfs_search_slot(root, BtrfsKey(450, 0, 0)) >>> print_extent_buffer(nodes[0]) leaf 30425088 level 0 items 184 generation 9 owner 5 leaf 30425088 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da ... item 179 key (450 INODE_ITEM 0) itemoff 4907 itemsize 160 generation 7 transid 7 size 4096 nbytes 12288 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 6 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417703.220000000 (2024-05-22 15:41:43) mtime 1716417703.220000000 (2024-05-22 15:41:43) otime 1716417703.220000000 (2024-05-22 15:41:43) item 180 key (450 INODE_REF 256) itemoff 4894 itemsize 13 index 195 namelen 3 name: 193 item 181 key (450 XATTR_ITEM 1640047104) itemoff 4857 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 182 key (450 EXTENT_DATA 0) itemoff 4804 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 8192 ram 12288 extent compression 0 (none) item 183 key (450 EXTENT_DATA 8192) itemoff 4751 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 Item 5 in the log tree corresponds to item 183 in the filesystem tree, but nothing matches item 4. Furthermore, item 183 is the last item in the leaf. btrfs_log_prealloc_extents() is responsible for logging prealloc extents beyond i_size. It first truncates any previously logged prealloc extents that start beyond i_size. Then, it walks the filesystem tree and copies the prealloc extent items to the log tree. If it hits the end of a leaf, then it calls btrfs_next_leaf(), which unlocks the tree and does another search. However, while the filesystem tree is unlocked, an ordered extent completion may modify the tree. In particular, it may insert an extent item that overlaps with an extent item that was already copied to the log tree. This may manifest in several ways depending on the exact scenario, including an EEXIST error that is silently translated to a full sync, overlapping items in the log tree, or this crash. This particular crash is triggered by the following sequence of events: - Initially, the file has i_size=4k, a regular extent from 0-4k, and a prealloc extent beyond i_size from 4k-12k. The prealloc extent item is the last item in its B-tree leaf. - The file is fsync'd, which copies its inode item and both extent items to the log tree. - An xattr is set on the file, which sets the BTRFS_INODE_COPY_EVERYTHING flag. - The range 4k-8k in the file is written using direct I/O. i_size is extended to 8k, but the ordered extent is still in flight. - The file is fsync'd. Since BTRFS_INODE_COPY_EVERYTHING is set, this calls copy_inode_items_to_log(), which calls btrfs_log_prealloc_extents(). - btrfs_log_prealloc_extents() finds the 4k-12k prealloc extent in the filesystem tree. Since it starts before i_size, it skips it. Since it is the last item in its B-tree leaf, it calls btrfs_next_leaf(). - btrfs_next_leaf() unlocks the path. - The ordered extent completion runs, which converts the 4k-8k part of the prealloc extent to written and inserts the remaining prealloc part from 8k-12k. - btrfs_next_leaf() does a search and finds the new prealloc extent 8k-12k. - btrfs_log_prealloc_extents() copies the 8k-12k prealloc extent into the log tree. Note that it overlaps with the 4k-12k prealloc extent that was copied to the log tree by the first fsync. - fsync calls btrfs_log_changed_extents(), which tries to log the 4k-8k extent that was written. - This tries to drop the range 4k-8k in the log tree, which requires adjusting the start of the 4k-12k prealloc extent in the log tree to 8k. - btrfs_set_item_key_safe() sees that there is already an extent starting at 8k in the log tree and calls BUG(). Fix this by detecting when we're about to insert an overlapping file extent item in the log tree and truncating the part that would overlap. CC: [email protected] # 6.1+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 79f18a4 ] When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Fixes: 0f3154e ("ionic: Add Tx and Rx handling") Signed-off-by: Taehee Yoo <[email protected]> Reviewed-by: Brett Creeley <[email protected]> Reviewed-by: Shannon Nelson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9d274c1 upstream. We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) #1 btrfs_drop_extents (fs/btrfs/file.c:411:4) #2 log_one_extent (fs/btrfs/tree-log.c:4732:9) #3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) #4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) #5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) #6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) #7 btrfs_sync_file (fs/btrfs/file.c:1933:8) #8 vfs_fsync_range (fs/sync.c:188:9) #9 vfs_fsync (fs/sync.c:202:9) #10 do_fsync (fs/sync.c:212:9) #11 __do_sys_fdatasync (fs/sync.c:225:9) #12 __se_sys_fdatasync (fs/sync.c:223:1) #13 __x64_sys_fdatasync (fs/sync.c:223:1) #14 do_syscall_x64 (arch/x86/entry/common.c:52:14) #15 do_syscall_64 (arch/x86/entry/common.c:83:7) #16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of the filesystem tree at the time of the crash: >>> root = prog.crashed_thread().stack_trace()[2]["inode"].root >>> ret, nodes, slots = btrfs_search_slot(root, BtrfsKey(450, 0, 0)) >>> print_extent_buffer(nodes[0]) leaf 30425088 level 0 items 184 generation 9 owner 5 leaf 30425088 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da ... item 179 key (450 INODE_ITEM 0) itemoff 4907 itemsize 160 generation 7 transid 7 size 4096 nbytes 12288 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 6 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417703.220000000 (2024-05-22 15:41:43) mtime 1716417703.220000000 (2024-05-22 15:41:43) otime 1716417703.220000000 (2024-05-22 15:41:43) item 180 key (450 INODE_REF 256) itemoff 4894 itemsize 13 index 195 namelen 3 name: 193 item 181 key (450 XATTR_ITEM 1640047104) itemoff 4857 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 182 key (450 EXTENT_DATA 0) itemoff 4804 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 8192 ram 12288 extent compression 0 (none) item 183 key (450 EXTENT_DATA 8192) itemoff 4751 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 Item 5 in the log tree corresponds to item 183 in the filesystem tree, but nothing matches item 4. Furthermore, item 183 is the last item in the leaf. btrfs_log_prealloc_extents() is responsible for logging prealloc extents beyond i_size. It first truncates any previously logged prealloc extents that start beyond i_size. Then, it walks the filesystem tree and copies the prealloc extent items to the log tree. If it hits the end of a leaf, then it calls btrfs_next_leaf(), which unlocks the tree and does another search. However, while the filesystem tree is unlocked, an ordered extent completion may modify the tree. In particular, it may insert an extent item that overlaps with an extent item that was already copied to the log tree. This may manifest in several ways depending on the exact scenario, including an EEXIST error that is silently translated to a full sync, overlapping items in the log tree, or this crash. This particular crash is triggered by the following sequence of events: - Initially, the file has i_size=4k, a regular extent from 0-4k, and a prealloc extent beyond i_size from 4k-12k. The prealloc extent item is the last item in its B-tree leaf. - The file is fsync'd, which copies its inode item and both extent items to the log tree. - An xattr is set on the file, which sets the BTRFS_INODE_COPY_EVERYTHING flag. - The range 4k-8k in the file is written using direct I/O. i_size is extended to 8k, but the ordered extent is still in flight. - The file is fsync'd. Since BTRFS_INODE_COPY_EVERYTHING is set, this calls copy_inode_items_to_log(), which calls btrfs_log_prealloc_extents(). - btrfs_log_prealloc_extents() finds the 4k-12k prealloc extent in the filesystem tree. Since it starts before i_size, it skips it. Since it is the last item in its B-tree leaf, it calls btrfs_next_leaf(). - btrfs_next_leaf() unlocks the path. - The ordered extent completion runs, which converts the 4k-8k part of the prealloc extent to written and inserts the remaining prealloc part from 8k-12k. - btrfs_next_leaf() does a search and finds the new prealloc extent 8k-12k. - btrfs_log_prealloc_extents() copies the 8k-12k prealloc extent into the log tree. Note that it overlaps with the 4k-12k prealloc extent that was copied to the log tree by the first fsync. - fsync calls btrfs_log_changed_extents(), which tries to log the 4k-8k extent that was written. - This tries to drop the range 4k-8k in the log tree, which requires adjusting the start of the 4k-12k prealloc extent in the log tree to 8k. - btrfs_set_item_key_safe() sees that there is already an extent starting at 8k in the log tree and calls BUG(). Fix this by detecting when we're about to insert an overlapping file extent item in the log tree and truncating the part that would overlap. CC: [email protected] # 6.1+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 79f18a4 ] When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Fixes: 0f3154e ("ionic: Add Tx and Rx handling") Signed-off-by: Taehee Yoo <[email protected]> Reviewed-by: Brett Creeley <[email protected]> Reviewed-by: Shannon Nelson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 79f18a4 ] When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Fixes: 0f3154e ("ionic: Add Tx and Rx handling") Signed-off-by: Taehee Yoo <[email protected]> Reviewed-by: Brett Creeley <[email protected]> Reviewed-by: Shannon Nelson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit a699781 ] A sysfs reader can race with a device reset or removal, attempting to read device state when the device is not actually present. eg: [exception RIP: qed_get_current_link+17] #8 [ffffb9e4f2907c48] qede_get_link_ksettings at ffffffffc07a994a [qede] #9 [ffffb9e4f2907cd8] __rh_call_get_link_ksettings at ffffffff992b01a3 #10 [ffffb9e4f2907d38] __ethtool_get_link_ksettings at ffffffff992b04e4 #11 [ffffb9e4f2907d90] duplex_show at ffffffff99260300 #12 [ffffb9e4f2907e38] dev_attr_show at ffffffff9905a01c #13 [ffffb9e4f2907e50] sysfs_kf_seq_show at ffffffff98e0145b #14 [ffffb9e4f2907e68] seq_read at ffffffff98d902e3 #15 [ffffb9e4f2907ec8] vfs_read at ffffffff98d657d1 #16 [ffffb9e4f2907f00] ksys_read at ffffffff98d65c3f #17 [ffffb9e4f2907f38] do_syscall_64 at ffffffff98a052fb crash> struct net_device.state ffff9a9d21336000 state = 5, state 5 is __LINK_STATE_START (0b1) and __LINK_STATE_NOCARRIER (0b100). The device is not present, note lack of __LINK_STATE_PRESENT (0b10). This is the same sort of panic as observed in commit 4224cfd ("net-sysfs: add check for netdevice being present to speed_show"). There are many other callers of __ethtool_get_link_ksettings() which don't have a device presence check. Move this check into ethtool to protect all callers. Fixes: d519e17 ("net: export device speed and duplex via sysfs") Fixes: 4224cfd ("net-sysfs: add check for netdevice being present to speed_show") Signed-off-by: Jamie Bainbridge <[email protected]> Link: https://patch.msgid.link/8bae218864beaa44ed01628140475b9bf641c5b0.1724393671.git.jamie.bainbridge@gmail.com Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 89a906d ] Floating point instructions in userspace can crash some arm kernels built with clang/LLD 17.0.6: BUG: unsupported FP instruction in kernel mode FPEXC == 0xc0000780 Internal error: Oops - undefined instruction: 0 [#1] ARM CPU: 0 PID: 196 Comm: vfp-reproducer Not tainted 6.10.0 #1 Hardware name: BCM2835 PC is at vfp_support_entry+0xc8/0x2cc LR is at do_undefinstr+0xa8/0x250 pc : [<c0101d50>] lr : [<c010a80c>] psr: a0000013 sp : dc8d1f68 ip : 60000013 fp : bedea19c r10: ec532b17 r9 : 00000010 r8 : 0044766c r7 : c0000780 r6 : ec532b17 r5 : c1c13800 r4 : dc8d1fb0 r3 : c10072c4 r2 : c0101c88 r1 : ec532b17 r0 : 0044766c Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 0251c008 DAC: 00000051 Register r0 information: non-paged memory Register r1 information: vmalloc memory Register r2 information: non-slab/vmalloc memory Register r3 information: non-slab/vmalloc memory Register r4 information: 2-page vmalloc region Register r5 information: slab kmalloc-cg-2k Register r6 information: vmalloc memory Register r7 information: non-slab/vmalloc memory Register r8 information: non-paged memory Register r9 information: zero-size pointer Register r10 information: vmalloc memory Register r11 information: non-paged memory Register r12 information: non-paged memory Process vfp-reproducer (pid: 196, stack limit = 0x61aaaf8b) Stack: (0xdc8d1f68 to 0xdc8d2000) 1f60: 0000081f b6f69300 0000000f c10073f4 c10072c4 dc8d1fb0 1f80: ec532b17 0c532b17 0044766c b6f9ccd8 00000000 c010a80c 00447670 60000010 1fa0: ffffffff c1c13800 00c5387d c0100f10 b6f68af8 00448fc0 00000000 bedea188 1fc0: bedea314 00000001 00448ebc b6f9d000 00447608 b6f9ccd8 00000000 bedea19c 1fe0: bede9198 bedea188 b6e1061c 0044766c 60000010 ffffffff 00000000 00000000 Call trace: [<c0101d50>] (vfp_support_entry) from [<c010a80c>] (do_undefinstr+0xa8/0x250) [<c010a80c>] (do_undefinstr) from [<c0100f10>] (__und_usr+0x70/0x80) Exception stack(0xdc8d1fb0 to 0xdc8d1ff8) 1fa0: b6f68af8 00448fc0 00000000 bedea188 1fc0: bedea314 00000001 00448ebc b6f9d000 00447608 b6f9ccd8 00000000 bedea19c 1fe0: bede9198 bedea188 b6e1061c 0044766c 60000010 ffffffff Code: 0a000061 e3877202 e594003c e3a0901 (eef16a10) ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Fatal exception in interrupt ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- This is a minimal userspace reproducer on a Raspberry Pi Zero W: #include <stdio.h> #include <math.h> int main(void) { double v = 1.0; printf("%fn", NAN + *(volatile double *)&v); return 0; } Another way to consistently trigger the oops is: calvin@raspberry-pi-zero-w ~$ python -c "import json" The bug reproduces only when the kernel is built with DYNAMIC_DEBUG=n, because the pr_debug() calls act as barriers even when not activated. This is the output from the same kernel source built with the same compiler and DYNAMIC_DEBUG=y, where the userspace reproducer works as expected: VFP: bounce: trigger ec532b17 fpexc c0000780 VFP: emulate: INST=0xee377b06 SCR=0x00000000 VFP: bounce: trigger eef1fa10 fpexc c0000780 VFP: emulate: INST=0xeeb40b40 SCR=0x00000000 VFP: raising exceptions 30000000 calvin@raspberry-pi-zero-w ~$ ./vfp-reproducer nan Crudely grepping for vmsr/vmrs instructions in the otherwise nearly idential text for vfp_support_entry() makes the problem obvious: vmlinux.llvm.good [0xc0101cb8] <+48>: vmrs r7, fpexc vmlinux.llvm.good [0xc0101cd8] <+80>: vmsr fpexc, r0 vmlinux.llvm.good [0xc0101d20] <+152>: vmsr fpexc, r7 vmlinux.llvm.good [0xc0101d38] <+176>: vmrs r4, fpexc vmlinux.llvm.good [0xc0101d6c] <+228>: vmrs r0, fpscr vmlinux.llvm.good [0xc0101dc4] <+316>: vmsr fpexc, r0 vmlinux.llvm.good [0xc0101dc8] <+320>: vmrs r0, fpsid vmlinux.llvm.good [0xc0101dcc] <+324>: vmrs r6, fpscr vmlinux.llvm.good [0xc0101e10] <+392>: vmrs r10, fpinst vmlinux.llvm.good [0xc0101eb8] <+560>: vmrs r10, fpinst2 vmlinux.llvm.bad [0xc0101cb8] <+48>: vmrs r7, fpexc vmlinux.llvm.bad [0xc0101cd8] <+80>: vmsr fpexc, r0 vmlinux.llvm.bad [0xc0101d20] <+152>: vmsr fpexc, r7 vmlinux.llvm.bad [0xc0101d30] <+168>: vmrs r0, fpscr vmlinux.llvm.bad [0xc0101d50] <+200>: vmrs r6, fpscr <== BOOM! vmlinux.llvm.bad [0xc0101d6c] <+228>: vmsr fpexc, r0 vmlinux.llvm.bad [0xc0101d70] <+232>: vmrs r0, fpsid vmlinux.llvm.bad [0xc0101da4] <+284>: vmrs r10, fpinst vmlinux.llvm.bad [0xc0101df8] <+368>: vmrs r4, fpexc vmlinux.llvm.bad [0xc0101e5c] <+468>: vmrs r10, fpinst2 I think LLVM's reordering is valid as the code is currently written: the compiler doesn't know the instructions have side effects in hardware. Fix by using "asm volatile" in fmxr() and fmrx(), so they cannot be reordered with respect to each other. The original compiler now produces working kernels on my hardware with DYNAMIC_DEBUG=n. This is the relevant piece of the diff of the vfp_support_entry() text, from the original oopsing kernel to a working kernel with this patch: vmrs r0, fpscr tst r0, #4096 bne 0xc0101d48 tst r0, #458752 beq 0xc0101ecc orr r7, r7, #536870912 ldr r0, [r4, #0x3c] mov r9, #16 -vmrs r6, fpscr orr r9, r9, #251658240 add r0, r0, #4 str r0, [r4, #0x3c] mvn r0, torvalds#159 sub r0, r0, #-1207959552 and r0, r7, r0 vmsr fpexc, r0 vmrs r0, fpsid +vmrs r6, fpscr and r0, r0, #983040 cmp r0, #65536 bne 0xc0101d88 Fixes: 4708fb0 ("ARM: vfp: Reimplement VFP exception entry in C code") Signed-off-by: Calvin Owens <[email protected]> Signed-off-by: Russell King (Oracle) <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Matt Fleming <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 6d00234 ] Function xen_pin_page calls xen_pte_lock, which in turn grab page table lock (ptlock). When locking, xen_pte_lock expect mm->page_table_lock to be held before grabbing ptlock, but this does not happen when pinning is caused by xen_mm_pin_all. This commit addresses lockdep warning below, which shows up when suspending a Xen VM. [ 3680.658422] Freezing user space processes [ 3680.660156] Freezing user space processes completed (elapsed 0.001 seconds) [ 3680.660182] OOM killer disabled. [ 3680.660192] Freezing remaining freezable tasks [ 3680.661485] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) [ 3680.685254] [ 3680.685265] ================================== [ 3680.685269] WARNING: Nested lock was not taken [ 3680.685274] 6.12.0+ #16 Tainted: G W [ 3680.685279] ---------------------------------- [ 3680.685283] migration/0/19 is trying to lock: [ 3680.685288] ffff88800bac33c0 (ptlock_ptr(ptdesc)#2){+.+.}-{3:3}, at: xen_pin_page+0x175/0x1d0 [ 3680.685303] [ 3680.685303] but this task is not holding: [ 3680.685308] init_mm.page_table_lock [ 3680.685311] [ 3680.685311] stack backtrace: [ 3680.685316] CPU: 0 UID: 0 PID: 19 Comm: migration/0 Tainted: G W 6.12.0+ #16 [ 3680.685324] Tainted: [W]=WARN [ 3680.685328] Stopper: multi_cpu_stop+0x0/0x120 <- __stop_cpus.constprop.0+0x8c/0xd0 [ 3680.685339] Call Trace: [ 3680.685344] <TASK> [ 3680.685347] dump_stack_lvl+0x77/0xb0 [ 3680.685356] __lock_acquire+0x917/0x2310 [ 3680.685364] lock_acquire+0xce/0x2c0 [ 3680.685369] ? xen_pin_page+0x175/0x1d0 [ 3680.685373] _raw_spin_lock_nest_lock+0x2f/0x70 [ 3680.685381] ? xen_pin_page+0x175/0x1d0 [ 3680.685386] xen_pin_page+0x175/0x1d0 [ 3680.685390] ? __pfx_xen_pin_page+0x10/0x10 [ 3680.685394] __xen_pgd_walk+0x233/0x2c0 [ 3680.685401] ? stop_one_cpu+0x91/0x100 [ 3680.685405] __xen_pgd_pin+0x5d/0x250 [ 3680.685410] xen_mm_pin_all+0x70/0xa0 [ 3680.685415] xen_pv_pre_suspend+0xf/0x280 [ 3680.685420] xen_suspend+0x57/0x1a0 [ 3680.685428] multi_cpu_stop+0x6b/0x120 [ 3680.685432] ? update_cpumasks_hier+0x7c/0xa60 [ 3680.685439] ? __pfx_multi_cpu_stop+0x10/0x10 [ 3680.685443] cpu_stopper_thread+0x8c/0x140 [ 3680.685448] ? smpboot_thread_fn+0x20/0x1f0 [ 3680.685454] ? __pfx_smpboot_thread_fn+0x10/0x10 [ 3680.685458] smpboot_thread_fn+0xed/0x1f0 [ 3680.685462] kthread+0xde/0x110 [ 3680.685467] ? __pfx_kthread+0x10/0x10 [ 3680.685471] ret_from_fork+0x2f/0x50 [ 3680.685478] ? __pfx_kthread+0x10/0x10 [ 3680.685482] ret_from_fork_asm+0x1a/0x30 [ 3680.685489] </TASK> [ 3680.685491] [ 3680.685491] other info that might help us debug this: [ 3680.685497] 1 lock held by migration/0/19: [ 3680.685500] #0: ffffffff8284df38 (pgd_lock){+.+.}-{3:3}, at: xen_mm_pin_all+0x14/0xa0 [ 3680.685512] [ 3680.685512] stack backtrace: [ 3680.685518] CPU: 0 UID: 0 PID: 19 Comm: migration/0 Tainted: G W 6.12.0+ #16 [ 3680.685528] Tainted: [W]=WARN [ 3680.685531] Stopper: multi_cpu_stop+0x0/0x120 <- __stop_cpus.constprop.0+0x8c/0xd0 [ 3680.685538] Call Trace: [ 3680.685541] <TASK> [ 3680.685544] dump_stack_lvl+0x77/0xb0 [ 3680.685549] __lock_acquire+0x93c/0x2310 [ 3680.685554] lock_acquire+0xce/0x2c0 [ 3680.685558] ? xen_pin_page+0x175/0x1d0 [ 3680.685562] _raw_spin_lock_nest_lock+0x2f/0x70 [ 3680.685568] ? xen_pin_page+0x175/0x1d0 [ 3680.685572] xen_pin_page+0x175/0x1d0 [ 3680.685578] ? __pfx_xen_pin_page+0x10/0x10 [ 3680.685582] __xen_pgd_walk+0x233/0x2c0 [ 3680.685588] ? stop_one_cpu+0x91/0x100 [ 3680.685592] __xen_pgd_pin+0x5d/0x250 [ 3680.685596] xen_mm_pin_all+0x70/0xa0 [ 3680.685600] xen_pv_pre_suspend+0xf/0x280 [ 3680.685607] xen_suspend+0x57/0x1a0 [ 3680.685611] multi_cpu_stop+0x6b/0x120 [ 3680.685615] ? update_cpumasks_hier+0x7c/0xa60 [ 3680.685620] ? __pfx_multi_cpu_stop+0x10/0x10 [ 3680.685625] cpu_stopper_thread+0x8c/0x140 [ 3680.685629] ? smpboot_thread_fn+0x20/0x1f0 [ 3680.685634] ? __pfx_smpboot_thread_fn+0x10/0x10 [ 3680.685638] smpboot_thread_fn+0xed/0x1f0 [ 3680.685642] kthread+0xde/0x110 [ 3680.685645] ? __pfx_kthread+0x10/0x10 [ 3680.685649] ret_from_fork+0x2f/0x50 [ 3680.685654] ? __pfx_kthread+0x10/0x10 [ 3680.685657] ret_from_fork_asm+0x1a/0x30 [ 3680.685662] </TASK> [ 3680.685267] xen:grant_table: Grant tables using version 1 layout [ 3680.685921] OOM killer enabled. [ 3680.685934] Restarting tasks ... done. Signed-off-by: Maksym Planeta <[email protected]> Reviewed-by: Juergen Gross <[email protected]> Message-ID: <[email protected]> Signed-off-by: Juergen Gross <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit ddc210c upstream. Fixed warning on PM resume as shown below caused due to uninitialized struct nand_operation that checks chip select field : WARN_ON(op->cs >= nanddev_ntargets(&chip->base) [ 14.588522] ------------[ cut here ]------------ [ 14.588529] WARNING: CPU: 0 PID: 1392 at drivers/mtd/nand/raw/internals.h:139 nand_reset_op+0x1e0/0x1f8 [ 14.588553] Modules linked in: bdc udc_core [ 14.588579] CPU: 0 UID: 0 PID: 1392 Comm: rtcwake Tainted: G W 6.14.0-rc4-g5394eea10651 #16 [ 14.588590] Tainted: [W]=WARN [ 14.588593] Hardware name: Broadcom STB (Flattened Device Tree) [ 14.588598] Call trace: [ 14.588604] dump_backtrace from show_stack+0x18/0x1c [ 14.588622] r7:00000009 r6:0000008b r5:60000153 r4:c0fa558c [ 14.588625] show_stack from dump_stack_lvl+0x70/0x7c [ 14.588639] dump_stack_lvl from dump_stack+0x18/0x1c [ 14.588653] r5:c08d40b0 r4:c1003cb0 [ 14.588656] dump_stack from __warn+0x84/0xe4 [ 14.588668] __warn from warn_slowpath_fmt+0x18c/0x194 [ 14.588678] r7:c08d40b0 r6:c1003cb0 r5:00000000 r4:00000000 [ 14.588681] warn_slowpath_fmt from nand_reset_op+0x1e0/0x1f8 [ 14.588695] r8:70c40dff r7:89705f41 r6:36b4a597 r5:c26c9444 r4:c26b0048 [ 14.588697] nand_reset_op from brcmnand_resume+0x13c/0x150 [ 14.588714] r9:00000000 r8:00000000 r7:c24f8010 r6:c228a3f8 r5:c26c94bc r4:c26b0040 [ 14.588717] brcmnand_resume from platform_pm_resume+0x34/0x54 [ 14.588735] r5:00000010 r4:c0840a50 [ 14.588738] platform_pm_resume from dpm_run_callback+0x5c/0x14c [ 14.588757] dpm_run_callback from device_resume+0xc0/0x324 [ 14.588776] r9:c24f8054 r8:c24f80a0 r7:00000000 r6:00000000 r5:00000010 r4:c24f8010 [ 14.588779] device_resume from dpm_resume+0x130/0x160 [ 14.588799] r9:c22539e4 r8:00000010 r7:c22bebb0 r6:c24f8010 r5:c22539dc r4:c22539b0 [ 14.588802] dpm_resume from dpm_resume_end+0x14/0x20 [ 14.588822] r10:c2204e40 r9:00000000 r8:c228a3fc r7:00000000 r6:00000003 r5:c228a414 [ 14.588826] r4:00000010 [ 14.588828] dpm_resume_end from suspend_devices_and_enter+0x274/0x6f8 [ 14.588848] r5:c228a414 r4:00000000 [ 14.588851] suspend_devices_and_enter from pm_suspend+0x228/0x2bc [ 14.588868] r10:c3502910 r9:c3501f40 r8:00000004 r7:c228a438 r6:c0f95e18 r5:00000000 [ 14.588871] r4:00000003 [ 14.588874] pm_suspend from state_store+0x74/0xd0 [ 14.588889] r7:c228a438 r6:c0f934c8 r5:00000003 r4:00000003 [ 14.588892] state_store from kobj_attr_store+0x1c/0x28 [ 14.588913] r9:00000000 r8:00000000 r7:f09f9f08 r6:00000004 r5:c3502900 r4:c0283250 [ 14.588916] kobj_attr_store from sysfs_kf_write+0x40/0x4c [ 14.588936] r5:c3502900 r4:c0d92a48 [ 14.588939] sysfs_kf_write from kernfs_fop_write_iter+0x104/0x1f0 [ 14.588956] r5:c3502900 r4:c3501f40 [ 14.588960] kernfs_fop_write_iter from vfs_write+0x250/0x420 [ 14.588980] r10:c0e14b48 r9:00000000 r8:c25f5780 r7:00443398 r6:f09f9f68 r5:c34f7f00 [ 14.588983] r4:c042a88c [ 14.588987] vfs_write from ksys_write+0x74/0xe4 [ 14.589005] r10:00000004 r9:c25f5780 r8:c02002fA0 r7:00000000 r6:00000000 r5:c34f7f00 [ 14.589008] r4:c34f7f00 [ 14.589011] ksys_write from sys_write+0x10/0x14 [ 14.589029] r7:00000004 r6:004421c0 r5:00443398 r4:00000004 [ 14.589032] sys_write from ret_fast_syscall+0x0/0x5c [ 14.589044] Exception stack(0xf09f9fa8 to 0xf09f9ff0) [ 14.589050] 9fa0: 00000004 00443398 00000004 00443398 00000004 00000001 [ 14.589056] 9fc0: 00000004 00443398 004421c0 00000004 b6ecbd58 00000008 bebfbc38 0043eb78 [ 14.589062] 9fe0: 00440eb0 bebfbaf8 b6de18a0 b6e579e8 [ 14.589065] ---[ end trace 0000000000000000 ]--- The fix uses the higher level nand_reset(chip, chipnr); where chipnr = 0, when doing PM resume operation in compliance with the controller support for single die nand chip. Switching from nand_reset_op() to nand_reset() implies more than just setting the cs field op->cs, it also reconfigures the data interface (ie. the timings). Tested and confirmed the NAND chip is in sync timing wise with host after the fix. Fixes: 97d90da ("mtd: nand: provide several helpers to do common NAND operations") Cc: [email protected] Signed-off-by: Kamal Dasu <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Miquel Raynal <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 866bafa ] There is a potential deadlock if we do report zones in an IO context, detailed in below lockdep report. When one process do a report zones and another process freezes the block device, the report zones side cannot allocate a tag because the freeze is already started. This can thus result in new block group creation to hang forever, blocking the write path. Thankfully, a new block group should be created on empty zones. So, reporting the zones is not necessary and we can set the write pointer = 0 and load the zone capacity from the block layer using bdev_zone_capacity() helper. ====================================================== WARNING: possible circular locking dependency detected 6.14.0-rc1 torvalds#252 Not tainted ------------------------------------------------------ modprobe/1110 is trying to acquire lock: ffff888100ac83e0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}, at: __flush_work+0x38f/0xb60 but task is already holding lock: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&q->q_usage_counter(queue)#16){++++}-{0:0}: blk_queue_enter+0x3d9/0x500 blk_mq_alloc_request+0x47d/0x8e0 scsi_execute_cmd+0x14f/0xb80 sd_zbc_do_report_zones+0x1c1/0x470 sd_zbc_report_zones+0x362/0xd60 blkdev_report_zones+0x1b1/0x2e0 btrfs_get_dev_zones+0x215/0x7e0 [btrfs] btrfs_load_block_group_zone_info+0x6d2/0x2c10 [btrfs] btrfs_make_block_group+0x36b/0x870 [btrfs] btrfs_create_chunk+0x147d/0x2320 [btrfs] btrfs_chunk_alloc+0x2ce/0xcf0 [btrfs] start_transaction+0xce6/0x1620 [btrfs] btrfs_uuid_scan_kthread+0x4ee/0x5b0 [btrfs] kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #2 (&fs_info->dev_replace.rwsem){++++}-{4:4}: down_read+0x9b/0x470 btrfs_map_block+0x2ce/0x2ce0 [btrfs] btrfs_submit_chunk+0x2d4/0x16c0 [btrfs] btrfs_submit_bbio+0x16/0x30 [btrfs] btree_write_cache_pages+0xb5a/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #1 (&fs_info->zoned_meta_io_lock){+.+.}-{4:4}: __mutex_lock+0x1aa/0x1360 btree_write_cache_pages+0x252/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}: __lock_acquire+0x2f52/0x5ea0 lock_acquire+0x1b1/0x540 __flush_work+0x3ac/0xb60 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 del_gendisk+0x841/0xa20 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 do_syscall_64+0x93/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e other info that might help us debug this: Chain exists of: (work_completion)(&(&wb->dwork)->work) --> &fs_info->dev_replace.rwsem --> &q->q_usage_counter(queue)#16 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&q->q_usage_counter(queue)#16); lock(&fs_info->dev_replace.rwsem); lock(&q->q_usage_counter(queue)#16); lock((work_completion)(&(&wb->dwork)->work)); *** DEADLOCK *** 5 locks held by modprobe/1110: #0: ffff88811f7bc108 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #1: ffff8881022ee0e0 (&shost->scan_mutex){+.+.}-{4:4}, at: scsi_remove_host+0x20/0x2a0 #2: ffff88811b4c4378 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #3: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 #4: ffffffffa3284360 (rcu_read_lock){....}-{1:3}, at: __flush_work+0xda/0xb60 stack backtrace: CPU: 0 UID: 0 PID: 1110 Comm: modprobe Not tainted 6.14.0-rc1 torvalds#252 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6a/0x90 print_circular_bug.cold+0x1e0/0x274 check_noncircular+0x306/0x3f0 ? __pfx_check_noncircular+0x10/0x10 ? mark_lock+0xf5/0x1650 ? __pfx_check_irq_usage+0x10/0x10 ? lockdep_lock+0xca/0x1c0 ? __pfx_lockdep_lock+0x10/0x10 __lock_acquire+0x2f52/0x5ea0 ? __pfx___lock_acquire+0x10/0x10 ? __pfx_mark_lock+0x10/0x10 lock_acquire+0x1b1/0x540 ? __flush_work+0x38f/0xb60 ? __pfx_lock_acquire+0x10/0x10 ? __pfx_lock_release+0x10/0x10 ? mark_held_locks+0x94/0xe0 ? __flush_work+0x38f/0xb60 __flush_work+0x3ac/0xb60 ? __flush_work+0x38f/0xb60 ? __pfx_mark_lock+0x10/0x10 ? __pfx___flush_work+0x10/0x10 ? __pfx_wq_barrier_func+0x10/0x10 ? __pfx___might_resched+0x10/0x10 ? mark_held_locks+0x94/0xe0 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 ? __pfx_bdi_unregister+0x10/0x10 ? up_write+0x1ba/0x510 del_gendisk+0x841/0xa20 ? __pfx_del_gendisk+0x10/0x10 ? _raw_spin_unlock_irqrestore+0x35/0x60 ? __pm_runtime_resume+0x79/0x110 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] ? kernfs_remove_by_name_ns+0xc0/0xf0 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 ? __pfx___mutex_unlock_slowpath+0x10/0x10 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 ? __pfx___do_sys_delete_module.isra.0+0x10/0x10 ? __pfx_slab_free_after_rcu_debug+0x10/0x10 ? kasan_save_stack+0x2c/0x50 ? kasan_record_aux_stack+0xa3/0xb0 ? __call_rcu_common.constprop.0+0xc4/0xfb0 ? kmem_cache_free+0x3a0/0x590 ? __x64_sys_close+0x78/0xd0 do_syscall_64+0x93/0x180 ? lock_is_held_type+0xd5/0x130 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? lockdep_hardirqs_on+0x78/0x100 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? __pfx___call_rcu_common.constprop.0+0x10/0x10 ? kmem_cache_free+0x3a0/0x590 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx___x64_sys_openat+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f436712b68b RSP: 002b:00007ffe9f1a8658 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 RAX: ffffffffffffffda RBX: 00005559b367fd80 RCX: 00007f436712b68b RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00005559b367fde8 RBP: 00007ffe9f1a8680 R08: 1999999999999999 R09: 0000000000000000 R10: 00007f43671a5fe0 R11: 0000000000000206 R12: 0000000000000000 R13: 00007ffe9f1a86b0 R14: 0000000000000000 R15: 0000000000000000 </TASK> Reported-by: Shin'ichiro Kawasaki <[email protected]> CC: <[email protected]> # 6.13+ Tested-by: Shin'ichiro Kawasaki <[email protected]> Reviewed-by: Damien Le Moal <[email protected]> Reviewed-by: Johannes Thumshirn <[email protected]> Signed-off-by: Naohiro Aota <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit ddc210c upstream. Fixed warning on PM resume as shown below caused due to uninitialized struct nand_operation that checks chip select field : WARN_ON(op->cs >= nanddev_ntargets(&chip->base) [ 14.588522] ------------[ cut here ]------------ [ 14.588529] WARNING: CPU: 0 PID: 1392 at drivers/mtd/nand/raw/internals.h:139 nand_reset_op+0x1e0/0x1f8 [ 14.588553] Modules linked in: bdc udc_core [ 14.588579] CPU: 0 UID: 0 PID: 1392 Comm: rtcwake Tainted: G W 6.14.0-rc4-g5394eea10651 #16 [ 14.588590] Tainted: [W]=WARN [ 14.588593] Hardware name: Broadcom STB (Flattened Device Tree) [ 14.588598] Call trace: [ 14.588604] dump_backtrace from show_stack+0x18/0x1c [ 14.588622] r7:00000009 r6:0000008b r5:60000153 r4:c0fa558c [ 14.588625] show_stack from dump_stack_lvl+0x70/0x7c [ 14.588639] dump_stack_lvl from dump_stack+0x18/0x1c [ 14.588653] r5:c08d40b0 r4:c1003cb0 [ 14.588656] dump_stack from __warn+0x84/0xe4 [ 14.588668] __warn from warn_slowpath_fmt+0x18c/0x194 [ 14.588678] r7:c08d40b0 r6:c1003cb0 r5:00000000 r4:00000000 [ 14.588681] warn_slowpath_fmt from nand_reset_op+0x1e0/0x1f8 [ 14.588695] r8:70c40dff r7:89705f41 r6:36b4a597 r5:c26c9444 r4:c26b0048 [ 14.588697] nand_reset_op from brcmnand_resume+0x13c/0x150 [ 14.588714] r9:00000000 r8:00000000 r7:c24f8010 r6:c228a3f8 r5:c26c94bc r4:c26b0040 [ 14.588717] brcmnand_resume from platform_pm_resume+0x34/0x54 [ 14.588735] r5:00000010 r4:c0840a50 [ 14.588738] platform_pm_resume from dpm_run_callback+0x5c/0x14c [ 14.588757] dpm_run_callback from device_resume+0xc0/0x324 [ 14.588776] r9:c24f8054 r8:c24f80a0 r7:00000000 r6:00000000 r5:00000010 r4:c24f8010 [ 14.588779] device_resume from dpm_resume+0x130/0x160 [ 14.588799] r9:c22539e4 r8:00000010 r7:c22bebb0 r6:c24f8010 r5:c22539dc r4:c22539b0 [ 14.588802] dpm_resume from dpm_resume_end+0x14/0x20 [ 14.588822] r10:c2204e40 r9:00000000 r8:c228a3fc r7:00000000 r6:00000003 r5:c228a414 [ 14.588826] r4:00000010 [ 14.588828] dpm_resume_end from suspend_devices_and_enter+0x274/0x6f8 [ 14.588848] r5:c228a414 r4:00000000 [ 14.588851] suspend_devices_and_enter from pm_suspend+0x228/0x2bc [ 14.588868] r10:c3502910 r9:c3501f40 r8:00000004 r7:c228a438 r6:c0f95e18 r5:00000000 [ 14.588871] r4:00000003 [ 14.588874] pm_suspend from state_store+0x74/0xd0 [ 14.588889] r7:c228a438 r6:c0f934c8 r5:00000003 r4:00000003 [ 14.588892] state_store from kobj_attr_store+0x1c/0x28 [ 14.588913] r9:00000000 r8:00000000 r7:f09f9f08 r6:00000004 r5:c3502900 r4:c0283250 [ 14.588916] kobj_attr_store from sysfs_kf_write+0x40/0x4c [ 14.588936] r5:c3502900 r4:c0d92a48 [ 14.588939] sysfs_kf_write from kernfs_fop_write_iter+0x104/0x1f0 [ 14.588956] r5:c3502900 r4:c3501f40 [ 14.588960] kernfs_fop_write_iter from vfs_write+0x250/0x420 [ 14.588980] r10:c0e14b48 r9:00000000 r8:c25f5780 r7:00443398 r6:f09f9f68 r5:c34f7f00 [ 14.588983] r4:c042a88c [ 14.588987] vfs_write from ksys_write+0x74/0xe4 [ 14.589005] r10:00000004 r9:c25f5780 r8:c02002fA0 r7:00000000 r6:00000000 r5:c34f7f00 [ 14.589008] r4:c34f7f00 [ 14.589011] ksys_write from sys_write+0x10/0x14 [ 14.589029] r7:00000004 r6:004421c0 r5:00443398 r4:00000004 [ 14.589032] sys_write from ret_fast_syscall+0x0/0x5c [ 14.589044] Exception stack(0xf09f9fa8 to 0xf09f9ff0) [ 14.589050] 9fa0: 00000004 00443398 00000004 00443398 00000004 00000001 [ 14.589056] 9fc0: 00000004 00443398 004421c0 00000004 b6ecbd58 00000008 bebfbc38 0043eb78 [ 14.589062] 9fe0: 00440eb0 bebfbaf8 b6de18a0 b6e579e8 [ 14.589065] ---[ end trace 0000000000000000 ]--- The fix uses the higher level nand_reset(chip, chipnr); where chipnr = 0, when doing PM resume operation in compliance with the controller support for single die nand chip. Switching from nand_reset_op() to nand_reset() implies more than just setting the cs field op->cs, it also reconfigures the data interface (ie. the timings). Tested and confirmed the NAND chip is in sync timing wise with host after the fix. Fixes: 97d90da ("mtd: nand: provide several helpers to do common NAND operations") Cc: [email protected] Signed-off-by: Kamal Dasu <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Miquel Raynal <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 88f7f56 ] When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush() generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC, which causes the flush_bio to be throttled by wbt_wait(). An example from v5.4, similar problem also exists in upstream: crash> bt 2091206 PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0" #0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8 #1 [ffff800084a2f820] __schedule at ffff800040bfa0c4 #2 [ffff800084a2f880] schedule at ffff800040bfa4b4 #3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4 #4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc #5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0 #6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254 #7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38 #8 [ffff800084a2fa60] generic_make_request at ffff800040570138 #9 [ffff800084a2fae0] submit_bio at ffff8000405703b4 #10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs] #11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs] #12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs] #13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs] #14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs] #15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs] #16 [ffff800084a2fdb0] process_one_work at ffff800040111d08 #17 [ffff800084a2fe00] worker_thread at ffff8000401121cc #18 [ffff800084a2fe70] kthread at ffff800040118de4 After commit 2def284 ("xfs: don't allow log IO to be throttled"), the metadata submitted by xlog_write_iclog() should not be throttled. But due to the existence of the dm layer, throttling flush_bio indirectly causes the metadata bio to be throttled. Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes wbt_should_throttle() return false to avoid wbt_wait(). Signed-off-by: Jinliang Zheng <[email protected]> Reviewed-by: Tianxiang Peng <[email protected]> Reviewed-by: Hao Peng <[email protected]> Signed-off-by: Mikulas Patocka <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit eedf3e3 ] ACPICA commit 1c28da2242783579d59767617121035dafba18c3 This was originally done in NetBSD: NetBSD/src@b69d1ac and is the correct alternative to the smattering of `memcpy`s I previously contributed to this repository. This also sidesteps the newly strict checks added in UBSAN: llvm/llvm-project@7926744 Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #1.2 0x000021982bc4af3c in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x41f3c #1.1 0x000021982bc4af3c in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x41f3c #1 0x000021982bc4af3c in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:395 <libclang_rt.asan.so>+0x41f3c #2 0x000021982bc4bb6f in handletype_mismatch_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:137 <libclang_rt.asan.so>+0x42b6f #3 0x000021982bc4b723 in __ubsan_handle_type_mismatch_v1 compiler-rt/lib/ubsan/ubsan_handlers.cpp:142 <libclang_rt.asan.so>+0x42723 #4 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #5 0x000021afcfdf2089 in acpi_rs_convert_aml_to_resource(struct acpi_resource*, union aml_resource*, struct acpi_rsconvert_info*) ../../third_party/acpica/source/components/resources/rsmisc.c:355 <platform-bus-x86.so>+0x6b2089 #6 0x000021afcfded169 in acpi_rs_convert_aml_to_resources(u8*, u32, u32, u8, void**) ../../third_party/acpica/source/components/resources/rslist.c:137 <platform-bus-x86.so>+0x6ad169 #7 0x000021afcfe2d24a in acpi_ut_walk_aml_resources(struct acpi_walk_state*, u8*, acpi_size, acpi_walk_aml_callback, void**) ../../third_party/acpica/source/components/utilities/utresrc.c:237 <platform-bus-x86.so>+0x6ed24a #8 0x000021afcfde66b7 in acpi_rs_create_resource_list(union acpi_operand_object*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rscreate.c:199 <platform-bus-x86.so>+0x6a66b7 #9 0x000021afcfdf6979 in acpi_rs_get_method_data(acpi_handle, const char*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rsutils.c:770 <platform-bus-x86.so>+0x6b6979 #10 0x000021afcfdf708f in acpi_walk_resources(acpi_handle, char*, acpi_walk_resource_callback, void*) ../../third_party/acpica/source/components/resources/rsxface.c:731 <platform-bus-x86.so>+0x6b708f #11 0x000021afcfa95dcf in acpi::acpi_impl::walk_resources(acpi::acpi_impl*, acpi_handle, const char*, acpi::Acpi::resources_callable) ../../src/devices/board/lib/acpi/acpi-impl.cc:41 <platform-bus-x86.so>+0x355dcf #12 0x000021afcfaa8278 in acpi::device_builder::gather_resources(acpi::device_builder*, acpi::Acpi*, fidl::any_arena&, acpi::Manager*, acpi::device_builder::gather_resources_callback) ../../src/devices/board/lib/acpi/device-builder.cc:84 <platform-bus-x86.so>+0x368278 #13 0x000021afcfbddb87 in acpi::Manager::configure_discovered_devices(acpi::Manager*) ../../src/devices/board/lib/acpi/manager.cc:75 <platform-bus-x86.so>+0x49db87 #14 0x000021afcf99091d in publish_acpi_devices(acpi::Manager*, zx_device_t*, zx_device_t*) ../../src/devices/board/drivers/x86/acpi-nswalk.cc:95 <platform-bus-x86.so>+0x25091d #15 0x000021afcf9c1d4e in x86::X86::do_init(x86::X86*) ../../src/devices/board/drivers/x86/x86.cc:60 <platform-bus-x86.so>+0x281d4e #16 0x000021afcf9e33ad in λ(x86::X86::ddk_init::(anon class)*) ../../src/devices/board/drivers/x86/x86.cc:77 <platform-bus-x86.so>+0x2a33ad #17 0x000021afcf9e313e in fit::internal::target<(lambda at../../src/devices/board/drivers/x86/x86.cc:76:19), false, false, std::__2::allocator<std::byte>, void>::invoke(void*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:183 <platform-bus-x86.so>+0x2a313e #18 0x000021afcfbab4c7 in fit::internal::function_base<16UL, false, void(), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <platform-bus-x86.so>+0x46b4c7 #19 0x000021afcfbab342 in fit::function_impl<16UL, false, void(), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/function.h:315 <platform-bus-x86.so>+0x46b342 #20 0x000021afcfcd98c3 in async::internal::retained_task::Handler(async_dispatcher_t*, async_task_t*, zx_status_t) ../../sdk/lib/async/task.cc:24 <platform-bus-x86.so>+0x5998c3 #21 0x00002290f9924616 in λ(const driver_runtime::Dispatcher::post_task::(anon class)*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/dispatcher.cc:789 <libdriver_runtime.so>+0x10a616 #22 0x00002290f9924323 in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:788:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int>::invoke(void*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0x10a323 #23 0x00002290f9904b76 in fit::internal::function_base<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xeab76 #24 0x00002290f9904831 in fit::callback_impl<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::operator()(fit::callback_impl<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/function.h:471 <libdriver_runtime.so>+0xea831 #25 0x00002290f98d5adc in driver_runtime::callback_request::Call(driver_runtime::callback_request*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/callback_request.h:74 <libdriver_runtime.so>+0xbbadc #26 0x00002290f98e1e58 in driver_runtime::Dispatcher::dispatch_callback(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >) ../../src/devices/bin/driver_runtime/dispatcher.cc:1248 <libdriver_runtime.so>+0xc7e58 #27 0x00002290f98e4159 in driver_runtime::Dispatcher::dispatch_callbacks(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:1308 <libdriver_runtime.so>+0xca159 #28 0x00002290f9918414 in λ(const driver_runtime::Dispatcher::create_with_adder::(anon class)*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:353 <libdriver_runtime.so>+0xfe414 #29 0x00002290f991812d in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:351:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>>::invoke(void*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0xfe12d #30 0x00002290f9906fc7 in fit::internal::function_base<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xecfc7 #31 0x00002290f9906c66 in fit::function_impl<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/function.h:315 <libdriver_runtime.so>+0xecc66 #32 0x00002290f98e73d9 in driver_runtime::Dispatcher::event_waiter::invoke_callback(driver_runtime::Dispatcher::event_waiter*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.h:543 <libdriver_runtime.so>+0xcd3d9 #33 0x00002290f98e700d in driver_runtime::Dispatcher::event_waiter::handle_event(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/dispatcher.cc:1442 <libdriver_runtime.so>+0xcd00d #34 0x00002290f9918983 in async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event(async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>*, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/async_loop_owned_event_handler.h:59 <libdriver_runtime.so>+0xfe983 #35 0x00002290f9918b9e in async::wait_method<async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>, &async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event>::call_handler(async_dispatcher_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async/include/lib/async/cpp/wait.h:201 <libdriver_runtime.so>+0xfeb9e #36 0x00002290f99bf509 in async_loop_dispatch_wait(async_loop_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async-loop/loop.c:394 <libdriver_runtime.so>+0x1a5509 #37 0x00002290f99b9958 in async_loop_run_once(async_loop_t*, zx_time_t) ../../sdk/lib/async-loop/loop.c:343 <libdriver_runtime.so>+0x19f958 #38 0x00002290f99b9247 in async_loop_run(async_loop_t*, zx_time_t, _Bool) ../../sdk/lib/async-loop/loop.c:301 <libdriver_runtime.so>+0x19f247 #39 0x00002290f99ba962 in async_loop_run_thread(void*) ../../sdk/lib/async-loop/loop.c:860 <libdriver_runtime.so>+0x1a0962 #40 0x000041afd176ef30 in start_c11(void*) ../../zircon/third_party/ulib/musl/pthread/pthread_create.c:63 <libc.so>+0x84f30 #41 0x000041afd18a448d in thread_trampoline(uintptr_t, uintptr_t) ../../zircon/system/ulib/runtime/thread.cc:100 <libc.so>+0x1ba48d Link: acpica/acpica@1c28da22 Signed-off-by: Rafael J. Wysocki <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Tamir Duberstein <[email protected]> [ rjw: Pick up the tag from Tamir ] Signed-off-by: Rafael J. Wysocki <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

Alexander Duyck and others added 30 commits September 30, 2016 10:12

Linux 4.7.6

f849d45

drm/nouveau/fifo/nv04: avoid ramht race against cookie insertion

b5a7c19

commit 666ca3d upstream. Signed-off-by: Ilia Mirkin <[email protected]> Signed-off-by: Ben Skeggs <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Uh oh!

Merge v4.7.10 which is latest 4.7.y stable version. #16

Merge v4.7.10 which is latest 4.7.y stable version. #16

Uh oh!

bkrepo commented Oct 28, 2016

Uh oh!

Uh oh!

Merge v4.7.10 which is latest 4.7.y stable version. #16

Are you sure you want to change the base?

Merge v4.7.10 which is latest 4.7.y stable version. #16

Uh oh!

Conversation

bkrepo commented Oct 28, 2016

Uh oh!

Uh oh!